Latest Firmware Releases

Technical Help / Firmwares for the Audi R8 Gen2 and Lamborghini Huracan Awd Controllers
Ryan.g
Syvecs Staff - Caretaker
Posts: 498
Joined: Fri May 30, 2008 4:05 pm

Latest Firmware Releases

Post by Ryan.g »

This thread is for tracking the firmware builds of the AWD Huracan / R8 units. When a new release is available it will be added to the end of this thread.

Help on updating the firmware can found in the via this YouTube Help video - https://www.youtube.com/watch?v=RuXkm_9gBRU

Any further Questions please E-mail support@syvecs.co.uk or speak to your nearest dealer
Last edited by Ryan.g on Tue May 04, 2021 2:33 pm, edited 1 time in total.
Ryan.g
Syvecs Staff - Caretaker
Posts: 498
Joined: Fri May 30, 2008 4:05 pm

1.14.2

Post by Ryan.g »

This is the first public release level

Please ensure you are using the Latest Ssuite software which has USB support - http://www.syvecs.com/forum/viewtopic.php?f=8&t=122

Help on updating the firmware can found in the via this YouTube Help video - https://www.youtube.com/watch?v=RuXkm_9gBRU

IMPORTANT: The AWD Firmware is locked to the AWD Hardware. While you will be able to flash the Enc file for a Huracan onto say a R35GTR unit, it will not come online as the hardware key will not match. Ensure you load the correct code.

Firmware Version 1.14.2 - www.syvecs.com/downloads/AWD_Huracan.enc
Last edited by Ryan.g on Tue May 04, 2021 2:33 pm, edited 1 time in total.
Ryan.g
Syvecs Staff - Caretaker
Posts: 498
Joined: Fri May 30, 2008 4:05 pm

1.15

Post by Ryan.g »

Version 1.15 contains the following updates

*Change Light Output Pin (HBR4)
*Drive ratio calculation for Gear detection on Manual Trans cars
*Enable Gear Detection from Drive Ratio option
*Change Light Min Speed
*Change Light RPM
*Change Light Min Tps


Please ensure you are using the Latest Ssuite software which has USB support - http://www.syvecs.com/forum/viewtopic.php?f=8&t=122

Help on updating the firmware can found in the via this YouTube Help video - https://www.youtube.com/watch?v=RuXkm_9gBRU

IMPORTANT: The AWD Firmware is locked to the AWD Hardware. While you will be able to flash the Enc file for a Huracan onto say a R35GTR unit, it will not come online as the hardware key will not match. Ensure you load the correct code.

Firmware Version 1.15.2 - www.syvecs.com/downloads/AWD_HuracanR8.enc
Ryan.g
Syvecs Staff - Caretaker
Posts: 498
Joined: Fri May 30, 2008 4:05 pm

15.3

Post by Ryan.g »

Version 1.15.3 contains a background change to send out the paddle up can frame for autoshift with R8

www.syvecs.com/downloads/AWD_HuracanR8_153.enc
Ryan.g
Syvecs Staff - Caretaker
Posts: 498
Joined: Fri May 30, 2008 4:05 pm

1.18 Firmware

Post by Ryan.g »

Version 1.18 contains the following updates

Changes since 1.15

1.16 - Added CanLogging option - New software will be released soon which allows you to monitor and log the canbus via USB
1.17 - CarCode Map Added for 997 Platform
1.18 - Added simple Map locking and Restriction option. - Press C, F inside a map


Please ensure you are using the Latest Ssuite software which has USB support - http://www.syvecs.com/forum/viewtopic.php?f=8&t=122

Help on updating the firmware can found in the via this YouTube Help video - https://www.youtube.com/watch?v=RuXkm_9gBRU

IMPORTANT: The AWD Firmware is locked to the AWD Hardware. While you will be able to flash the Enc file for a Huracan onto say a R35GTR unit, it will not come online as the hardware key will not match. Ensure you load the correct code.

Firmware Version 1.18 - www.syvecs.com/downloads/AWD_HuracanR8_1-18-1.enc
Ryan.g
Syvecs Staff - Caretaker
Posts: 498
Joined: Fri May 30, 2008 4:05 pm

1.21 Firmware

Post by Ryan.g »

Version 1.21 contains the following updates

Changes since 1.18
V1.19 Output Testing added
V1.21 Output mode on changelight output to Lowside, Yaris HandBrake disable test mode light on dash in Burnout, Gear displayed in breakpoint, MAP1 Multiplier, post shift Multiplier to help stop spin after drivetrain torque change



Please ensure you are using the Latest Ssuite software which has USB support - http://www.syvecs.com/forum/viewtopic.php?f=8&t=122

Help on updating the firmware can found in the via this YouTube Help video - https://www.youtube.com/watch?v=RuXkm_9gBRU

IMPORTANT: The AWD Firmware is locked to the AWD Hardware. While you will be able to flash the Enc file for a Huracan onto say a R35GTR unit, it will not come online as the hardware key will not match. Ensure you load the correct code.

Firmware Version 1.21 - www.syvecs.com/downloads/AWD_HuracanR8_1-21-1.enc
Ryan.g
Syvecs Staff - Caretaker
Posts: 498
Joined: Fri May 30, 2008 4:05 pm

1.21.2

Post by Ryan.g »

Version 1.21.2 contains the following updates

Changes since 1.12.1
Receive of Snow Mode on Audi R8
Receive of Handbrake



Please ensure you are using the Latest Ssuite software which has USB support - http://www.syvecs.com/forum/viewtopic.php?f=8&t=122

Help on updating the firmware can found in the via this YouTube Help video - https://www.youtube.com/watch?v=RuXkm_9gBRU

IMPORTANT: The AWD Firmware is locked to the AWD Hardware. While you will be able to flash the Enc file for a Huracan onto say a R35GTR unit, it will not come online as the hardware key will not match. Ensure you load the correct code.

Firmware Version 1.21 - www.syvecs.com/downloads/AWD_HuracanR8_1-21-2.enc
Ryan.g
Syvecs Staff - Caretaker
Posts: 498
Joined: Fri May 30, 2008 4:05 pm

1.23 Firmware - X4

Post by Ryan.g »

In order to improve manufacturing time we have made dedicated AWD boards based on the new X4 GEN2 hardware. Because of this a different version of firmware and calibration is required for these boards as they have selectable pull ups for the inputs.

Orders placed from July 2022 will have these boards and look like the below. If you have this version and wish to update the firmware then use the X4 version attached. Older hardware use the normal AWD version.

Image

Changes since 1.21:

V1.22 - Adjustable the Yaris display bars vs duty to match more OEM, SnowMode on the R35GTR selects AwdSel3
V1.23 - Added Gear Duty Multiplier

Please ensure you are using the Latest Ssuite software which has USB support - http://www.syvecs.com/forum/viewtopic.php?f=8&t=122

Help on updating the firmware can found in the via this YouTube Help video - https://www.youtube.com/watch?v=RuXkm_9gBRU

IMPORTANT: The AWD Firmware is locked to the AWD Hardware. While you will be able to flash the Enc file for a Huracan onto say a R35GTR unit, it will not come online as the hardware key will not match. Ensure you load the correct code.

OLD BOARD - Firmware Version 1.23 - www.syvecs.com/downloads/AWD_HuracanR8_1-23-1.enc
NEW BOARD - Firmware Version 1.23 - www.syvecs.com/downloads/X4AWD_HuracanR8_1-23-1.enc
Ryan.g
Syvecs Staff - Caretaker
Posts: 498
Joined: Fri May 30, 2008 4:05 pm

1.23.3

Post by Ryan.g »

In order to improve manufacturing time we have made dedicated AWD boards based on the new X4 GEN2 hardware. Because of this a different version of firmware and calibration is required for these boards as they have selectable pull ups for the inputs.

Orders placed from July 2022 will have these boards and look like the below. If you have this version and wish to update the firmware then use the X4 version attached. Older hardware use the normal AWD version.

Image

Changes since 1.23.1:

*Bugfix with AwdSel and key on

Please ensure you are using the Latest Ssuite software which has USB support - http://www.syvecs.com/forum/viewtopic.php?f=8&t=122

Help on updating the firmware can found in the via this YouTube Help video - https://www.youtube.com/watch?v=RuXkm_9gBRU

IMPORTANT: The AWD Firmware is locked to the AWD Hardware. While you will be able to flash the Enc file for a Huracan onto say a R35GTR unit, it will not come online as the hardware key will not match. Ensure you load the correct code.

OLD BOARD - Firmware Version 1.23.3 - www.syvecs.com/downloads/AWD_HuracanR8_1-23-3.enc
NEW BOARD - Firmware Version 1.23.3 - www.syvecs.com/downloads/X4AWD_HuracanR8_1-23-3.enc
Ryan.g
Syvecs Staff - Caretaker
Posts: 498
Joined: Fri May 30, 2008 4:05 pm

1.24

Post by Ryan.g »

In order to improve manufacturing time we have made dedicated AWD boards based on the new X4 GEN2 hardware. Because of this a different version of firmware and calibration is required for these boards as they have selectable pull ups for the inputs.

Orders placed from July 2022 will have these boards and look like the below. If you have this version and wish to update the firmware then use the X4 version attached. Older hardware use the normal AWD version.

Image

Changes since 1.23.3:

*Added MQB4 Support on X4AWD Hardware
*Changed Burnout/2WD mode to take priority over Hold decay so 0% is applied instantly

Please ensure you are using the Latest Ssuite software which has USB support - http://www.syvecs.com/forum/viewtopic.php?f=8&t=122

Help on updating the firmware can found in the via this YouTube Help video - https://www.youtube.com/watch?v=RuXkm_9gBRU

IMPORTANT: The AWD Firmware is locked to the AWD Hardware. While you will be able to flash the Enc file for a Huracan onto say a R35GTR unit, it will not come online as the hardware key will not match. Ensure you load the correct code.

OLD BOARD - Firmware Version 1.24.4 - www.syvecs.com/downloads/AWD_HuracanR8_1-24-4.enc
NEW BOARD - Firmware Version 1.24.4 - www.syvecs.com/downloads/X4AWD_HuracanR8_1-24-4.enc
Post Reply