Page 4 of 4
Re: 2008 Subaru does not start
Posted: Mon Jun 26, 2017 2:04 pm
by TimH
Don't think that's the correct diagram. It's B136-20 for the starter control - that matches all the hatch loom adapters I've ever made.
Relay on the loom adapter is to power up the DBW system in the correct manner.
Re: 2008 Subaru does not start
Posted: Mon Jun 26, 2017 2:12 pm
by west_minist
Ok. No contact from Syvecs yet.
What makes it a little urgent too, the guy has a maf connector issue. So to get it in and start working would be great.
Re: 2008 Subaru does not start
Posted: Wed Jun 28, 2017 6:30 am
by west_minist
Tim:
Good news!!!
A wonderful Syvecs personnel, who was on vacation help me review the setup. After bridging the starting motor, we was purring on the Syvecs.
We have some harness issues and we have to get a diagram for them. All equipment will be shipped back for testing. I am going to request that we use the S6Plis to replace the clutter we have now.
But I must say the support personnel was super professional and extremely helpful.
Re: 2008 Subaru does not start
Posted: Wed Jun 28, 2017 8:41 am
by stevieturbo
Good result!
Re: 2008 Subaru does not start
Posted: Wed Jun 28, 2017 9:17 am
by TimH
Good news
Re: 2008 Subaru does not start
Posted: Sun Jul 02, 2017 9:28 pm
by west_minist
Tim:
When you see INJ5 (#13), what is the #13?
Good news:
I received an update for the CAN that I can see the led flashing.
Boyan came in and she is running well. We drive it around the block, but she now have to be worked on. As soon as the CAN is sorted, we will attempt to install permanently (car is a daily drive), tune and make sure all is well.
Thank you.
Re: 2008 Subaru does not start
Posted: Sun Jul 02, 2017 9:32 pm
by stevieturbo
Good question...and partial answer.
it isnt really the 13'th output but on the excel file of the pinout schedule, it's listed as INJ5 #13
http://www.syvecs.com/downloads/Pinouts ... inouts.xls
Re: 2008 Subaru does not start
Posted: Sun Jul 02, 2017 9:49 pm
by west_minist
I ask because you have fuel 13 to 16.
Re: 2008 Subaru does not start
Posted: Sun Jul 02, 2017 10:55 pm
by west_minist
FUEL 01 - INJ 01
FUEL 02 - INJ 02
FUEL 03 - INJ 03
FUEL 04 - INJ 04
FUEL 05 - INJ 05
FUEL 06 - INJ 06
FUEL 07 - INJ 07
FUEL 08 - INJ 08
FUEL 09 - PWM1 - AUX1
FUEL 10 - PWM2 - AUX2
FUEL 11 - PWM3 - AUX3
FUEL 12 - PWM4 - AUX4
FUEL 13 - PWM5 - AUX5
FUEL 14 - PWM6 - AUX6
FUEL 15 - PWM7 - AUX7
FUEL 16 - PWM8 - AUX8
Re: 2008 Subaru does not start
Posted: Wed Jul 12, 2017 1:18 pm
by west_minist
Good news everyone. We Ryan help (Boyan too), we re-position the pins on the CAN cable and she is now communicating and key starting.
I am certain the pins were right, but there are now.
The next step is to schedule the installation and start tuning.
Thank you for the great support.