Pet hate of mine...WHY OH WHY use AFR!!! Lambda is fuel independent. AFR is meaningless unless you know the precise fuel mixture, which is hit and miss with pump fuel at the best of times.
Stick with lambda units, IMHO
Search found 718 matches
- Thu Jun 24, 2021 7:54 pm
- Forum: S6 GP/PnP Technical
- Topic: Lambda to afr
- Replies: 13
- Views: 12064
- Sun May 09, 2021 8:36 pm
- Forum: General Syvecs Chat
- Topic: Syvecs map sensor identification
- Replies: 17
- Views: 8567
Re: Syvecs map sensor identification
I doubt the calibration is the same, but the relavant data is printed on it. If you don't know how to interpret it wait until a mapper can check and tweak the Cal.
- Sun May 09, 2021 5:43 pm
- Forum: General Syvecs Chat
- Topic: Syvecs map sensor identification
- Replies: 17
- Views: 8567
Re: Syvecs map sensor identification
If you buy a reputable replacement sensor it should come with a calibration sheet. A KA sensor for example is nominally 0.5V=0bar and 4.5V=full range but it will have a spec sheet with it stating the 0 bar voltage "offset" (typically within a few mV of 0.5V, e.g. 0.498V) and "span&quo...
- Sat May 08, 2021 1:58 pm
- Forum: General Syvecs Chat
- Topic: Engine trip error code 1013
- Replies: 2
- Views: 8246
Re: Engine trip error code 1013
You probably need to update the Toucan firmware; earlier versions didn't decode all of the messages there are now and, also, the un-decoded error code was incorrectly displayed! 1013 is, I'm pretty sure, actually error 113 which would be "Coolant Pressure Trip" so is something you should g...
- Sat Apr 03, 2021 12:26 pm
- Forum: Feature Requests
- Topic: Stack data stream addition
- Replies: 15
- Views: 34342
Re: Stack data stream addition
The Syvecs CAN echo uses a Syvecs-specific protocol (which got changed without notice recently by the way) to encode the frame/slots of the CAN stream directly. I would be very surprised if any other Dash happened to use the same protocol, but I guess it's possible. The first thing to get hold of wo...
- Mon Mar 01, 2021 12:54 pm
- Forum: General Syvecs Chat
- Topic: Connecting Racelogic VBox to Svvecs CAN system
- Replies: 8
- Views: 5259
Re: Connecting Racelogic VBox to Svvecs CAN system
S6 is only 1Mbit/s, unless you connect an I/O expander in which case it runs a bespoke, non-standard, 1.3Mbit/s point-to-point CAN link that cannot be shared with other devices. S6+ has a built in I/O expander on an internal CAN bus and an outward-facing CANbus that is connected vi an internal "...
- Tue Dec 29, 2020 8:02 pm
- Forum: S7-I / S7Plus Technical
- Topic: Flex fuel sensor
- Replies: 7
- Views: 5641
Re: Flex fuel sensor
Set the input type to Bipolar. Only the AU types need to be set to thermistor. Found that out myself a few years ago even though it's counter-intuitive when the sensor "needs" a pullup enabled so you'd think thermistor for sure.
- Sun Oct 11, 2020 6:09 pm
- Forum: Subaru
- Topic: Oil pressure fluctuation and AVCS fluctuation
- Replies: 19
- Views: 28352
- Mon Sep 14, 2020 10:58 am
- Forum: S8 Technical
- Topic: audi coils
- Replies: 2
- Views: 7494
Re: audi coils
I've wired these in for people a few times for various ECUs.
Apart from +12V and the trigger, there are two grounds. One is supposed to be taken back to ground pins at the ECU and the other taken to the engine block. They worked for me wired like that, anyway!
Apart from +12V and the trigger, there are two grounds. One is supposed to be taken back to ground pins at the ECU and the other taken to the engine block. They worked for me wired like that, anyway!
- Mon Jul 20, 2020 11:51 am
- Forum: General Syvecs Chat
- Topic: Ignition Final volatile
- Replies: 2
- Views: 5646
Re: Ignition Final volatile
cyl02knockIgnRtd?