Search found 51 matches
- Thu Apr 13, 2017 8:43 am
- Forum: S8 Technical
- Topic: Gearbox Control option?
- Replies: 6
- Views: 17437
Re: Gearbox Control option?
would be great if a "help video" of setting up paddle shift was available. like the gear cut/blip video. or a fully configured base map with it all set up as a start point was available. there is alot of tables to populate. just a starting point of having a tune from a car running the syst...
- Thu Apr 13, 2017 8:25 am
- Forum: General Syvecs Chat
- Topic: 0-5v OUTPUT
- Replies: 6
- Views: 12334
Re: 0-5v OUTPUT
thanks for the replies. good info.
the other option is sending the pwm to the on switch of the controller. was on $26 aud. il have a play with it when im closer to starting the engine.. cheers.
the other option is sending the pwm to the on switch of the controller. was on $26 aud. il have a play with it when im closer to starting the engine.. cheers.
- Sun Apr 09, 2017 11:19 am
- Forum: General Syvecs Chat
- Topic: Ignition coil recommendation
- Replies: 7
- Views: 21167
Re: Ignition coil recommendation
Get a M&W cdi (M&W PRO-16 @ 3.00min mark in video below), end of all misfire problems. Will work with stock 2JZ coils too. Video here, you can even see the CDI box, look carefully > https://www.youtube.com/watch?v=Fyo98Ao9nTo There is allot of stupid shit in the video, but remember this is ...
- Sun Apr 09, 2017 10:37 am
- Forum: General Syvecs Chat
- Topic: 0-5v OUTPUT
- Replies: 6
- Views: 12334
Re: 0-5v OUTPUT
its a kinsler 0.7" spur gear pump that i have put a 3000rpm 12v motor on the back of.(1hp) the motor mimics the back of a dry sump oil pump with a hex drive pump option. we have found that with 1200hp+ atw with e85. the magnafuel efi 750 just doesnt quite do it. ( low hp low rpm motor) and havi...
- Sat Apr 08, 2017 10:15 am
- Forum: General Syvecs Chat
- Topic: 0-5v OUTPUT
- Replies: 6
- Views: 12334
0-5v OUTPUT
Hello, i have an older s12, and have a very large fuel pump. (hand me down from the shop racecar) (20L/min@80psi) i have a speed controller for it. its a 60 amp dc motor speed controller via pwm. but i will need a 0-5v output from the ecu to replace the trimpot that is on the controller. how would i...
- Thu Apr 28, 2016 2:46 pm
- Forum: Feature Requests
- Topic: LOW IMPEDANCE INJECTOR battery voltage latency
- Replies: 5
- Views: 14305
Re: LOW IMPEDANCE INJECTOR battery voltage latency
some of the stuff im working with now, (2500hp 2j etc etc) running 2200cc pri 5500cc sec on methanol. (currently on a m150 "package") super hard to navigate the software if you dont use motec m1 stuff daily! ie trying to set up a extra 2 step switch to hold the rpm down while staging rathe...
- Thu Apr 28, 2016 2:36 pm
- Forum: Feature Requests
- Topic: gearbox input rpm for slipper clutch
- Replies: 1
- Views: 9780
gearbox input rpm for slipper clutch
hey all, would be good to have an input for a clutch input shaft rpm sensor and tail-shaft speed to map a run to help with slipper/with lock up solenoid, clutch settings in a drag car scenario or to the point some dedicated drag racing strategies to help with logging and clutch/traction control sett...
- Thu Oct 29, 2015 9:10 am
- Forum: Feature Requests
- Topic: ENGINE PRE OILING PUMP/ACCUSUMP control
- Replies: 2
- Views: 9072
Re: ENGINE PRE OILING PUMP/ACCUSUMP control
thanks pat. nice reply. i actually have a pre oil pump on my evo pajero to stop the death rattle. super ghetto using a hobbs switch. power from the start solenoid supplies a ssr. start signal powers the pump and when oil pressure is reached it switches the relay sending power to the starter solenoid...
- Thu Oct 29, 2015 8:55 am
- Forum: Feature Requests
- Topic: LOW IMPEDANCE INJECTOR battery voltage latency
- Replies: 5
- Views: 14305
Re: LOW IMPEDANCE INJECTOR battery voltage latency
i though so. how would one get a accurate latency data with the use of a ballast resistor? (this is for a s8)
perhaps do the sequential/batch fire running modes and play with latency values till a similar afr is achieved?
perhaps do the sequential/batch fire running modes and play with latency values till a similar afr is achieved?
- Thu Oct 22, 2015 11:18 am
- Forum: Feature Requests
- Topic: LOW IMPEDANCE INJECTOR battery voltage latency
- Replies: 5
- Views: 14305
LOW IMPEDANCE INJECTOR battery voltage latency
hello,
can we have a latency table for low impedance injectors, same as for saturation high impedance injectors?
is it also silly to ask for the ability to run staged injection using both high and low impedance injectors? (small hi imp primary, big low imp sec)?
cheers.
can we have a latency table for low impedance injectors, same as for saturation high impedance injectors?
is it also silly to ask for the ability to run staged injection using both high and low impedance injectors? (small hi imp primary, big low imp sec)?
cheers.