Search found 51 matches

by T04GTR
Mon Jun 26, 2017 2:06 pm
Forum: Feature Requests
Topic: SYVECS branded 100 amp pwm dc controler
Replies: 2
Views: 11142

Re: SYVECS branded 100 amp pwm dc controler

i really should just get a euro 600w pwm fab module. audi/merc. the problem im having is finding the pwm frequency they use to control the thing. short of going to a car yard with a multimeter and probing the control wire when its on...

its off say a 2004 s500 merc.
DSC_0318.JPG
DSC_0318.JPG (543.8 KiB) Viewed 11275 times
by T04GTR
Fri Jun 23, 2017 12:18 pm
Forum: S8 Technical
Topic: Gearbox Control option?
Replies: 6
Views: 17426

Re: Gearbox Control option?

:D
by T04GTR
Fri Jun 23, 2017 12:10 pm
Forum: X10 (Legacy - Gen1)
Topic: PDU "INDUCTIVE LOAD"
Replies: 0
Views: 25547

PDU "INDUCTIVE LOAD"

Hello, i cant use my pdu to run the fuel pumps in team mode, and switched to inductive load. it keeps tripping instantly. each of the 2 outputs control 1 walbro 450 e85 pump. 15 amp running. works fine when not set to inductive load. when set to inductive, with the fuse/inrush tuned way up to the ma...
by T04GTR
Fri Jun 23, 2017 12:05 pm
Forum: Feature Requests
Topic: SYVECS branded 100 amp pwm dc controler
Replies: 2
Views: 11142

SYVECS branded 100 amp pwm dc controler

Hello, not really a feature in the ecu, but a stand-alone dc motor pwm module of decent current rating 50-100 amp. that accepts the common negative switched pwm signal. im having problems finding a easy to configure/wire fan controller. (my fan sucks 55 amp when on flat out and 155amp inrush) w215 b...
by T04GTR
Fri Jun 16, 2017 2:40 pm
Forum: General Syvecs Chat
Topic: Unable to edit sensor linearization breakpoints
Replies: 5
Views: 12094

Re: Unable to edit sensor linearization breakpoints

AWSOME!! was really looking for this when doing a twin dbw engine with 2 slightly different sensor voltages at the default zero voltage
by T04GTR
Fri Jun 16, 2017 2:35 pm
Forum: S8 Technical
Topic: DBW Wiring/config
Replies: 7
Views: 19830

Re: DBW Wiring/config

with regards to the sensor table. i wish i could input the ACTUAL sensor voltage in regards to the percentage. ie the opposite of whats there. (you have to pick a set voltage that is "near enough" to what you are seeing from the sensor. rather than having a table with 0 to 100% and inputti...
by T04GTR
Wed May 24, 2017 1:17 pm
Forum: S8 Technical
Topic: DBW Wiring/config
Replies: 7
Views: 19830

Re: DBW Wiring/config

just as a side note, i recently set up a vq35hr with 2 dbw. my thoughts on what was the correct way to wire it up was to hook up a battery to the motor, + and - quickly apply power to OPEN the throttle. and that would determine the polarity. (i had a basemap) (please can we input sensor voltages for...
by T04GTR
Wed May 24, 2017 12:37 pm
Forum: Feature Requests
Topic: ABILITY TO INPUT SENSOR VOLTAGES TO CALIBRATE
Replies: 1
Views: 8894

ABILITY TO INPUT SENSOR VOLTAGES TO CALIBRATE

hey, not sure if it can be done, but i would like to be able to input an exact voltage of a sensor to calibrate it properly. ie for 2 dbw throttles, tps 0% etc etc.
cheers.
by T04GTR
Wed May 24, 2017 12:32 pm
Forum: General Syvecs Chat
Topic: sensor scales
Replies: 4
Views: 9035

Re: sensor scales

ok cool, yes i understand now. i figured so. also, with regards to the scales, how do i change the voltage numbers. ie: i want to put in 0.50v and 4.5v. and then interpolate. also i found when setting up the dbw tps voltage, it would be nice to be able to input the exact voltage to get the 0% spot o...
by T04GTR
Tue May 16, 2017 1:14 pm
Forum: General Syvecs Chat
Topic: sensor scales
Replies: 4
Views: 9035

sensor scales

hey all, just a quick question. how can i change the sensor scales in sensor linearisation y scale? ie: i have a 5 bar guage sensor i want to use for crank case pressure, (i know its a big sensor for that, but had it around) how can i change the scale on the left? it wont let me edit the max pressur...