Search found 51 matches
- Sat Jan 27, 2018 7:43 am
- Forum: Feature Requests
- Topic: rev cut per gear
- Replies: 16
- Views: 35221
Re: rev cut per gear
could the 36-2-2-2 crank trigger be playing a part? theres got to be 1000's of r35's out there. what am i doing wrong.
- Sat Jan 27, 2018 5:46 am
- Forum: Feature Requests
- Topic: rev cut per gear
- Replies: 16
- Views: 35221
Re: rev cut per gear
yes, i have a cal for burnouts with no launch. and can turn knock off. but it is just the noisy backfiring violence of the "rpm limit" vs the cut that i have issue with. eg. car in neutral, rev limit set to say 6500. mash the pedal and all sorts of flames and backfiring out the exhaust.. w...
- Fri Jan 26, 2018 1:25 pm
- Forum: S6-I / S6Plus Technical
- Topic: Controlling fuel pumps with solid state relay pwm
- Replies: 12
- Views: 44104
Re: Controlling fuel pumps with solid state relay pwm
be very very careful, and fit a proper flyback diode. and a 1k resister between the ssr b+ and trigger + and the ecu. i killed 2 outputs on my s12 when i was trying to get a ssr to run a big engine fan. in short. the relay failed (closed circuit) and because i didnt have a resister between the b+ an...
- Fri Jan 26, 2018 1:09 pm
- Forum: Feature Requests
- Topic: rev cut per gear
- Replies: 16
- Views: 35221
Re: rev cut per gear
yes, i understand that. its not like im trying to hit it. but doing a burnout in a car with paddle shift can be a little tricky, especially one thats making alot of power and having a very "revy" nature. also quite hard to modulate the throttle with big sticky drag radials on a prepped sur...
- Fri Jan 26, 2018 6:59 am
- Forum: S8 Technical
- Topic: REV LIMIT
- Replies: 1
- Views: 6851
REV LIMIT
Hello, had to remove the "rev limit" (well put it 200rpm above the rev cut) because the engine hated life with it. knock control going crazy, popping and banging out the exhaust etc etc. tried ignition type, fuel type, instant and average speed measure and a variety of fuel and ignition cu...
- Fri Jan 26, 2018 6:56 am
- Forum: Feature Requests
- Topic: rev cut per gear
- Replies: 16
- Views: 35221
rev cut per gear
Hello, had to remove the "rev limit" (well put it 200rpm above the rev cut) because the engine hated life with it. knock control going crazy, popping and banging out the exhaust etc etc. tried ignition type, fuel type, instant and average speed measure and a variety of fuel and ignition cu...
- Sat Dec 30, 2017 9:43 am
- Forum: General Syvecs Chat
- Topic: KnockWarnLight - how to test
- Replies: 5
- Views: 11100
Re: KnockWarnLight - how to test
with the smd700, i set it up to alert me when knock ign retard was >2 degrees.. etc etc for all cylinders. so when i knocks i can quickly see if a cylinder is prone.
- Wed Oct 25, 2017 11:34 am
- Forum: Feature Requests
- Topic: LOW LOAD CUT adder (full auto gear control)
- Replies: 0
- Views: 33217
LOW LOAD CUT adder (full auto gear control)
hello, would be nice to be able to switch between either pps or manifold pressure for the low load gear cut threshold for turbo charged engines. eg: say low load cut is 20% throttle. going up a hill or constant 20% is enough to build boost slowly, to the point where the low load cut severity fuel cu...
- Fri Sep 01, 2017 4:09 pm
- Forum: General Syvecs Chat
- Topic: cylinder trims
- Replies: 3
- Views: 7324
Re: cylinder trims
that did it. cheers
- Thu Aug 31, 2017 1:22 pm
- Forum: General Syvecs Chat
- Topic: Knock sensor - shielded cable?
- Replies: 11
- Views: 22491
Re: Knock sensor - shielded cable?
technically, probs a good idea. but twisted should be fine. i know alot of oem use single core shielded. ie assuming signal on the inside and gnd as the shield. unless the loom has the knock sensor wires running parallel next to the coil or injector wires or hopefully not next to a cdi box or someth...