Search found 123 matches
- Fri Nov 18, 2016 7:10 pm
- Forum: General
- Topic: New I/O Expander - Now Released!
- Replies: 8
- Views: 32457
Re: New I/O Expander - Now Released!
just finalising a software variant (again selectable from the PC software) to allow the unit to emulate the (very expensive!!) LR/Syvecs 50Hz GPS unit. This allows G sensor and accelerometer data (lateral/longitudinal/vertical G and yaw/pitch/roll), along with 50Hz speed data, GPS latitude, longitu...
- Fri Nov 18, 2016 2:07 pm
- Forum: General Syvecs Chat
- Topic: Engine Speed Controlled outputs - HOWTO?
- Replies: 2
- Views: 5136
Re: Engine Speed Controlled outputs - HOWTO?
OK, having a couple of extra minutes on my hands in the 40deg C heat today, I played around with this control again, and found it is actually quite easy. What makes it difficult to figure out is that SCal only shows which speed control band is active, not whether the output is actually on or off. We...
- Thu Nov 17, 2016 3:58 pm
- Forum: General Syvecs Chat
- Topic: Using Maths channel to calculate turbo airflow
- Replies: 18
- Views: 44439
Re: Using Maths channel to calculate turbo airflow
To save that view to include the new maths channel, simply go to Worksheet and Save Worksheet, give it the same name as the currently selected one ("Tuning" in your case), and choose to overwrite it.
- Thu Nov 17, 2016 12:22 pm
- Forum: S8 Technical
- Topic: S8 Thermocouple Wiring
- Replies: 5
- Views: 16138
Re: S8 Thermocouple Wiring
And both sensors are defined in I/O Configuration->Pin Assignments->Exhaust gas temp as per the pic? Sorry if that sounds very basic, but sadly I have no other bright ideas.
- Wed Nov 16, 2016 8:25 pm
- Forum: General Syvecs Chat
- Topic: SView - little pointer on X & Y-axis
- Replies: 2
- Views: 5757
Re: SView - little pointer on X & Y-axis
The blue arrow at the bottom (10.2) shows the lowest value for the selected channel, in the time series you currently have onscreen (~15:10 to 15:13 in your screenshot). The arrow at the top (18.3) shows the highest value for the selected time series, and the 12.9 on the left shows the average value...
- Wed Nov 16, 2016 8:21 pm
- Forum: General Syvecs Chat
- Topic: Engine Speed Controlled outputs - HOWTO?
- Replies: 2
- Views: 5136
Engine Speed Controlled outputs - HOWTO?
Can anyone give me a tip, or explain the logic of the Eng Speed outputs? I played around with one, and can't seem to grasp the logic behind it. If I set it to stepped intervals, i.e. 1000rpm, 1500, 2000, etc, it seems to switch the output on and off at alternating points, i.e. off at 1000, on at 150...
- Wed Nov 16, 2016 9:36 am
- Forum: S8 Technical
- Topic: S8 Thermocouple Wiring
- Replies: 5
- Views: 16138
Re: S8 Thermocouple Wiring
From your post, it seems you have a flat linearization for the K-Type sensors, correct? If not, please make sure to set the EGT sensor linearizations to "0" throughout.
- Wed Nov 09, 2016 8:48 am
- Forum: General Syvecs Chat
- Topic: Unable to edit sensor linearization breakpoints
- Replies: 5
- Views: 12202
Re: Unable to edit sensor linearization breakpoints
I did it the same as Tim: Select li N earization, then S elect Type, select interpolated or extrapolated (or other) as required, then li N earization and E dit Points, add the values you have from your sensor provider, and then li N earization and A pply. Linearization.png Points.png Sensor.png
- Tue Nov 08, 2016 3:24 pm
- Forum: General Syvecs Chat
- Topic: Finding stuff in Scal
- Replies: 2
- Views: 5359
Re: Finding stuff in Scal
There certainly is.
Just press Cal, then Goto, then start to type your search term.
Just press Cal, then Goto, then start to type your search term.
- Fri Sep 09, 2016 6:17 pm
- Forum: General
- Topic: New I/O Expander - Now Released!
- Replies: 8
- Views: 32457
Re: New I/O Expander - Now Released!
Thank Tim
Forgot to mention I'm on a S6, and already using the CANbus, so I will wait around for the "passthrough" version.
Paul
Forgot to mention I'm on a S6, and already using the CANbus, so I will wait around for the "passthrough" version.
Paul