Search found 527 matches
- Mon Nov 27, 2017 5:41 am
- Forum: General Syvecs Chat
- Topic: Launch Control strategy
- Replies: 6
- Views: 13651
Re: Launch Control strategy
Hugh, With a GTR the by far best way to get it off the line or in fact on most cars is to setup the Launch in Stage which is normally is by default on the GTR base maps. Here you can setup a RPM Limit based on Vehicle speed or time. With 4wd if its likely you could spin the front wheels where Vehicl...
- Mon Nov 27, 2017 5:35 am
- Forum: S8 Technical
- Topic: Analog inputs filtering routine
- Replies: 4
- Views: 11841
Re: Analog inputs filtering routine
Its always best to have the filtering OFF in my experiences for the Crank and Cam, if you are experiences noise on these it important to fix it properly via better wiring setup. There is no difference in the filtering between the AN Inputs. Using AN09 and AN11 for the Crank and cam is fine on a S8. ...
- Mon Nov 27, 2017 5:31 am
- Forum: S6-I / S6Plus Technical
- Topic: Torque Estimation
- Replies: 4
- Views: 13068
Re: Torque Estimation
See the manual on the R35GTR kit here - http://www.syvecs.com/downloads/Syvecs%20SGTR%20Manual%20S6+.pdf The only way that the ECU would drop torque at the engine is if the EngTrqLim value was active from a TCM Request or if the User Enabled "Enable Torque Limitation By driver Demand" What...
- Tue Oct 24, 2017 2:01 pm
- Forum: S6 GP/PnP Technical
- Topic: Latest S6 Firmware
- Replies: 33
- Views: 176794
Re: Latest S6 Firmware
This Link - CLICK HERE is for version 1.84 of the S6 firmware. PLEASE ENSURE LATEST SSUITE SOFTWARE IS IN USE BEFORE UPGRADING FIRMWARE!!! Updates from 1.79 * change range of als bypass disable tps to allow 125% threshold * allow negative values in als tps timeout threshold for deliberate never-time...
- Wed Aug 23, 2017 10:02 pm
- Forum: General Syvecs Chat
- Topic: Defi and Syvecs 4bar disagreement!
- Replies: 32
- Views: 58308
Re: Defi and Syvecs 4bar disagreement!
0mbar = 0v
1000mbar = 1.20v
4000mbar = 4.75v
1000mbar = 1.20v
4000mbar = 4.75v
- Tue Aug 22, 2017 10:40 am
- Forum: General Syvecs Chat
- Topic: Defi and Syvecs 4bar disagreement!
- Replies: 32
- Views: 58308
Re: Defi and Syvecs 4bar disagreement!
Gents, Over the years we have had 2 different versions of the 4bar Map sensors after having some issues with transducer suppliers a while back. The output between the 2 sensors are slightly different and hence why the voltage point is supplied with the sensor. I will remove the 4Bar from the Sensor ...
- Sun Jul 23, 2017 5:27 am
- Forum: S6 GP/PnP Technical
- Topic: 2JZ VVTI Drive by wire control!
- Replies: 12
- Views: 27896
Re: 2JZ VVTI Drive by wire control!
The Supra VVTI is another of the Toyota DBW throttles which should of been recalled. The internal design and also pot B output from the sensors was only useful up to 40%, above that there is no way to validate and hence the A/B Validation is ignored above that in the VVTI Base maps. After 40% tps it...
- Thu Jul 06, 2017 12:09 pm
- Forum: Software
- Topic: Math function in SCal
- Replies: 4
- Views: 16331
Re: Math function in SCal
List of updates and fixes in Software Sticky
- Thu Jun 08, 2017 8:59 am
- Forum: S12 Technical
- Topic: Latest S12 Firmware
- Replies: 13
- Views: 82931
Re: Latest S12 Firmware
This Link is for version 1.590 of the S12 firmware. PLEASE ENSURE LATEST SSUITE SOFTWARE IS IN USE BEFORE UPGRADING FIRMWARE!!! Changes since 1.578 * driveRatioError available as cm axis * lapDistance available as cm axis * tacho in via gen can rx (when using the ECU as a GCU/logger with engine cont...
- Thu Jun 08, 2017 8:58 am
- Forum: S8 Technical
- Topic: Latest S8C Firmware
- Replies: 24
- Views: 96527
Re: Latest S8C Firmware
This Link is for version 1.590 of the S8 firmware. PLEASE ENSURE LATEST SSUITE SOFTWARE IS IN USE BEFORE UPGRADING FIRMWARE!!! Changes since 1.578 * driveRatioError available as cm axis * lapDistance available as cm axis * tacho in via gen can rx (when using the ECU as a GCU/logger with engine contr...