Search found 70 matches

by Trickster
Mon Apr 25, 2022 4:50 pm
Forum: General Syvecs Chat
Topic: resonance flaps: change light or configurable map?
Replies: 3
Views: 4208

Re: resonance flaps: change light or configurable map?

As far as i am aware from my own setup, the shift light stages remain on even when others are activated.

You could also use engine speed controlled outputs A & B? If they arent already used.

Or spare Fan On/Off?

Graeme
by Trickster
Sun Apr 03, 2022 8:14 pm
Forum: General Syvecs Chat
Topic: Any possibility of Real Dash support?
Replies: 30
Views: 43934

Re: Any possibility of Real Dash support?

Hey Any updated info or xml file etc on this? Anything to get this setup pain free would be ideal. I literally just bought the can to usb as i already have an in car pc (just an intel i5, 8gb ram, 128gb ssd) for audio and to use smon sdata etc while driving, but tired of the syvecs smon look haha Al...
by Trickster
Fri Dec 17, 2021 11:43 pm
Forum: General Syvecs Chat
Topic: Syvecs Ultimate Customer support ! (Story)
Replies: 3
Views: 9365

Re: Syvecs Ultimate Customer support ! (Story)

I have had the S6GP for 5 years now, and considering this one time.purchase (I'd buy and build more if I had the money believe me) the support I have had off Ryan (who had always tuned my car previously also) has been second to none

Syvecs really is an amazing outfit

Graeme
by Trickster
Thu Nov 18, 2021 7:41 pm
Forum: General Syvecs Chat
Topic: S6 Plus EGT fault
Replies: 3
Views: 2656

Re: S6 Plus EGT fault

Sounds like you connected the new sensors up reverse polarity, they read opposite so it would show the temp reducing

Graeme
by Trickster
Sat Oct 23, 2021 11:45 pm
Forum: S7-I / S7Plus Technical
Topic: Blip to rev match
Replies: 4
Views: 5336

Re: Blip to rev match

On my h pattern I use a brake switch and a clutch switch at the bottom of the clutch pedal, when both are depressed it gives a blip request (input as gear blip direct into ecu but I use a canbus circuit board to save inputs) Then in gear blip settings you can select how much the throttle opens and f...
by Trickster
Sat Oct 23, 2021 11:39 pm
Forum: S6-I / S6Plus Technical
Topic: S6 Firmware
Replies: 4
Views: 5444

Re: S6 Firmware

It is a shame that there will be no updates, I have a couple of issues which are not the end of the world and I can work around them, but still it would be nice, like unlocking the canbus generic recieve haha
by Trickster
Thu Apr 15, 2021 4:01 pm
Forum: General Syvecs Chat
Topic: Crank and Cam Trigger Sync on LS7
Replies: 9
Views: 7643

Re: Crank and Cam Trigger Sync on LS7

Put the wheel sensor into the old crank sensor location

Graeme
by Trickster
Fri Oct 02, 2020 9:21 pm
Forum: Technical Deposit
Topic: Power Steering Pressure Input for Idle duty adder
Replies: 4
Views: 13401

Re: Power Steering Pressure Input for Idle duty adder

Well if you have a spare input you can install a pressure sensor and use it as a custom sensor, then create a custom map based on that input (and another like tps etc if you want a 3d map) to add idle duty I know the battery one seems like it would have a delay, but it actually works great, I don't ...
by Trickster
Mon Jun 08, 2020 11:48 pm
Forum: Technical Deposit
Topic: Power Steering Pressure Input for Idle duty adder
Replies: 4
Views: 13401

Re: Power Steering Pressure Input for Idle duty adder

Just seen this and it's an issue I have also, sometimes when stationary with my fans and fuel pumps running the car would bog and cut out as I turned the wheel. Also sometimes when fans kicked in, at night moreso with lights etc I made a custom table to increasing add idle duty against baterry volta...
by Trickster
Sat Jun 06, 2020 11:37 am
Forum: General Syvecs Chat
Topic: More water / meth injection
Replies: 99
Views: 2473550

Re: More water / meth injection

Yeh I know mate, I was just being funny because there are no more firmware updates haha