Search found 123 matches

by Slowie
Thu Jun 29, 2023 8:12 pm
Forum: Software
Topic: Datalogging not stopping
Replies: 4
Views: 8025

Re: Datalogging not stopping

Was this ever resolved? It's an unusual fault, would be good to know what caused it.
by Slowie
Thu Jan 26, 2023 7:09 pm
Forum: General Syvecs Chat
Topic: Using Fuel Consumption Volume Rate in strategies?
Replies: 5
Views: 4791

Re: Using Fuel Consumption Volume Rate in strategies?

That's quite an interesting read. I have also had issues with huge spikes in DIP (specifically on VAG engines) when rapidly closing the throttle. Have not tried too hard to solve it until recently, but now have an older engine where the spikes go over the max "safe" pressure of the sensor,...
by Slowie
Wed Dec 14, 2022 6:19 pm
Forum: General Syvecs Chat
Topic: Learn Maps - committing to base maps?
Replies: 3
Views: 3433

Re: Learn Maps - committing to base maps?

Hi

When you are viewing the actual learning correction map (e.g. Base Wastegate Control Duty Learning / Learned Correction 1) you can use the Learn menu (top right) to apply or reset the learned correction to the base map.
by Slowie
Mon Nov 14, 2022 12:27 pm
Forum: S7-I / S7Plus Technical
Topic: S7Plus connect to AIM MXL Datalogger
Replies: 8
Views: 7161

Re: S7Plus connect to AIM MXL Datalogger

Hi Yes, you can use RS232. Never used it personally on a S7. only others. If you run the S7 RS232 wire to the dash, you should be able to select either Pectel as ECU Manufacturer with T2/T6 as the ECU Model, or LIFE as the ECU Manufacturer and Stack as the ECU Model. Then in SCAL set Datastreams -> ...
by Slowie
Thu Nov 10, 2022 5:26 pm
Forum: S7-I / S7Plus Technical
Topic: S7Plus connect to AIM MXL Datalogger
Replies: 8
Views: 7161

Re: S7Plus connect to AIM MXL Datalogger

Hi If it is an original MXL dash (not MXL2), you will need Race Studio 2. To setup the datastream you need to connect the dash to CAN2 on the ECU, set Datastreams->Generic CAN Transmit->Transmit Bus to CAN2 on all items, and using Race Studio 2 change your dashboard config to use the Life Racing F88...
by Slowie
Thu Jun 02, 2022 3:04 pm
Forum: S7-I / S7Plus Technical
Topic: need some dbw help
Replies: 32
Views: 22628

Re: need some dbw help

These ECU's aren't known for reading battery voltage that accurately, but 7V is wrong. Hope something didn't get damaged.

You could perhaps try swapping the DBW wires to H-Bridge 3 or 4 (Slaveout 5+6 or slave out 7+8), to see if the h-bridge is damaged.
by Slowie
Wed Jun 01, 2022 6:34 pm
Forum: S7-I / S7Plus Technical
Topic: need some dbw help
Replies: 32
Views: 22628

Re: need some dbw help

Hi Just want to confirm, do you have one or two DBW throttle bodies on your car? Your config seems to indicate one. Also, do you have one or two wires to the DBW motor from the ECU? (Are Slave Out 1 and Slave Out 2 both wired to the same DBW throttle body? Or two different ones?) Normally, if runnin...
by Slowie
Mon May 30, 2022 8:08 pm
Forum: S7-I / S7Plus Technical
Topic: need some dbw help
Replies: 32
Views: 22628

Re: need some dbw help

The DBW PD table is not populated, I don't think it will attempt to move the throttle like that (Drive By WIre -> Position Control -> Proportional / Derivative Gain). The attached file has some values in, should get it moving. But you will have to calibrate it correctly for your throttle body, set b...
by Slowie
Mon Feb 08, 2021 2:37 pm
Forum: S7-I / S7Plus Technical
Topic: Torque limiter help
Replies: 1
Views: 3636

Re: Torque limiter help

Check your settings under Limiters -> Rev Limit -> Drive By Wire Closing
by Slowie
Tue Dec 08, 2020 4:23 pm
Forum: General Syvecs Chat
Topic: Pectel lambda sensors
Replies: 1
Views: 3553

Pectel lambda sensors

Hi

Does anyone know if there is a lambda calibration for Pectel NTK (band 10) sensors available? I only ask because I have a box full of brand new ones on the shelf.

Thanks