Search found 9 matches

by Laci
Tue Apr 23, 2013 8:28 am
Forum: S6 GP/PnP Technical
Topic: anti lag
Replies: 8
Views: 24144

Re: anti lag

KISS... Keep it simple stupid. No diffucer, just plain pipes from auxiliary air valve. Air entrance from cold side of IC and some ecu control strategy. Picture from 2002 Peugeot 206 WRC. Cold side feed, helps to prolong ALS - at least few milliseconds longer, before melt down. I DON'T want to make ...
by Laci
Thu Apr 18, 2013 11:57 am
Forum: S6 GP/PnP Technical
Topic: anti lag
Replies: 8
Views: 24144

Re: anti lag

Could ecu control another one throttle bypass valve (posteriorly built) in ALS mode by ALS setting: Bypass Duty Effect / Idle Stepper Control)? For example: through EGR output (EGR Mode: During Antilag). I need this because there is only in that case enough air for ALS operation when both valves are...
by Laci
Mon Apr 15, 2013 11:00 am
Forum: S6 GP/PnP Technical
Topic: NTK L2H2 (LZA-09-E1)
Replies: 4
Views: 9887

Re: NTK L2H2 (LZA-09-E1)

I checked again and set correctly the all settings of lambda sensor and now it works perfectly.
Thank you for your helping.
by Laci
Thu Mar 28, 2013 3:22 pm
Forum: S6 GP/PnP Technical
Topic: NTK L2H2 (LZA-09-E1)
Replies: 4
Views: 9887

Re: NTK L2H2 (LZA-09-E1)

Have you assigned and configured the heater output? The output voltage (set in Output Functions->Lambda Heaters) needs to be 10.7v throughout. There is a timer for full power heater which when on (for say 20 seconds) will distort the lambda reading to begin with, but you should get a good reading w...
by Laci
Thu Mar 28, 2013 10:07 am
Forum: S6 GP/PnP Technical
Topic: NTK L2H2 (LZA-09-E1)
Replies: 4
Views: 9887

NTK L2H2 (LZA-09-E1)

I would like to inquire how much time need the wideband lambda sensor to give signal after engine starting?
Type: NTK L2H2 (LZA-09-E1) connected directly to S6GP ecu (according to manual)

Thank you for your helping in advanced.

Laci.
by Laci
Wed Mar 20, 2013 4:01 pm
Forum: Mitsubishi
Topic: trigger disks
Replies: 10
Views: 34287

Re: trigger disks

Please send me an email address and I will send you it in a dwg.

Laci.
by Laci
Mon Jan 21, 2013 12:48 pm
Forum: Mitsubishi
Topic: trigger disks
Replies: 10
Views: 34287

Re: trigger disks

gaz@gr wrote:Has anyone made a trigger disk for the evo yet ?
Yes, custom 18-1 crank trigger wheel:
Image
by Laci
Fri Jun 22, 2012 9:39 am
Forum: S6 GP/PnP Technical
Topic: Sensors, inputs and ABS
Replies: 11
Views: 30302

Re: Sensors, inputs and ABS

Thank you very much.
by Laci
Sun Jun 17, 2012 7:57 am
Forum: S6 GP/PnP Technical
Topic: Sensors, inputs and ABS
Replies: 11
Views: 30302

Re: Sensors, inputs and ABS

See attached a example pinout sheet i have done for you and also see the below link on the S6GP which explains the inputs more. Hello, I started to built in a S6GP into a Lancer EVO VI TME, and it would be helpful if we could make a similar pinout sheet which could be used for wiring of EVO VI-Syve...