Search found 718 matches

by TimH
Fri Nov 17, 2023 10:39 am
Forum: Subaru
Topic: A/C pin assignment newage sti
Replies: 5
Views: 15643

Re: A/C pin assignment newage sti

stevieturbo wrote: Fri Nov 17, 2023 10:17 am For what purpose exactly ? I'd doubt the ECU master would be compatible ?
S6 cannot receive additional inputs via CAN. Is this S6?

If S7, with 2x CANbus, you can receive data via CAN and the ECU master expander can almost certainly be configured to work.
by TimH
Sun Oct 08, 2023 8:40 pm
Forum: S7-I / S7Plus Technical
Topic: S7-I and S7Plus Can1 Fixed Datastream - DBC
Replies: 17
Views: 44006

Re: S7-I and S7Plus Can1 Fixed Datastream - DBC

It's a limitation of the slave protocol rather than X10. Not enough bandwidth on the link to cope with much extra data.
by TimH
Sun Oct 08, 2023 11:08 am
Forum: S7-I / S7Plus Technical
Topic: S7-I and S7Plus Can1 Fixed Datastream - DBC
Replies: 17
Views: 44006

Re: S7-I and S7Plus Can1 Fixed Datastream - DBC

:!: Warning - my information might be a few years out of date but I am 99.9% sure it still applies :!: The "slave" protocol runs in a non-standard fashion, at a non-standard data rate. It both transmits and receives "slave" data frames over the CAN link and is (pretty much) exclu...
by TimH
Mon Sep 04, 2023 7:37 pm
Forum: General Syvecs Chat
Topic: Syvecs Tiny dash
Replies: 9
Views: 7119

Re: Syvecs Tiny dash

Does it even support OBDII data?
by TimH
Wed Mar 29, 2023 6:36 pm
Forum: S7-I / S7Plus Technical
Topic: Electronic Steering
Replies: 14
Views: 16929

Re: Electronic Steering

stevieturbo wrote: Wed Mar 29, 2023 6:35 pm I don't have one here to test, so can't say.

But it would be unusual, yes.
I doi...but on holiday...I'll make a note to investigate this when i get back :ugeek:
by TimH
Wed Mar 29, 2023 6:05 pm
Forum: S7-I / S7Plus Technical
Topic: Electronic Steering
Replies: 14
Views: 16929

Re: Electronic Steering

I have heard quite a few people report S7 outputs causing relays to turn on when the ECU is off. Whilst Stevie is right - it is best not to have a relay powered by a permanent live - I personally do not think it right that an ECU output can sink enough current to turn on a relay when the output is o...
by TimH
Fri Mar 10, 2023 10:13 am
Forum: S7-I / S7Plus Technical
Topic: Can receive question for rotary switches wheel speed ect.
Replies: 1
Views: 6133

Re: Can receive question for rotary switches wheel speed ect.

As a general reply, if you assign X-CAN to a device/sensor then the scaling of the received data should match the format that would be used in the transmit stream. In the case of a CAL switch I believe that means it will expect 1, 2, 3 etc, rather than the mV equivalent/replication of an electrical ...
by TimH
Tue Jan 03, 2023 8:01 pm
Forum: Software
Topic: Playback function
Replies: 5
Views: 14927

Re: Playback function

According to the manual it's to: "Playback recorded calibration adjustments (engine dyno use)"
by TimH
Thu Oct 13, 2022 12:57 pm
Forum: General Syvecs Chat
Topic: Anti lag hardware/software setup
Replies: 14
Views: 10332

Re: Anti lag hardware/software setup

If you only want ALS active while the switch is pushed, you can use a momentary switch without issue. The software doesn't know the mechanical construction of the switch. If you want a press/release of the momentary switch to turn it on, and a second press/release to turn it off then, as has been sa...
by TimH
Thu Aug 18, 2022 6:45 pm
Forum: General Syvecs Chat
Topic: Motec CAN Programming for 2 Syvecs 50Hz Receivers
Replies: 8
Views: 9659

Re: Motec CAN Programming for 2 Syvecs 50Hz Receivers

Only way to differentiate between the 2 GPS receivers is they each transmit data using unique CAN IDs. There's nothing you can do at the MoTeC end to magically distinguish data that is received on the same CAN ID from 2 different devices. I don't think there is a user interface to change the CAN IDs...